2000 Civic Oil Drain Pan Plug Problem

I'd say the place that just did the change stripped out the drain plug,
and offered you an 'oversized' excuse.



jelgie.RemoveThis@gmail.com wrote:

>I took my car into a place to have the oil changed today. They said
>that the last mechanic had installed an oversized oil drain pan plug
>and that it would likely leak. Sure enough... I brought it home and it
>leaked. The mechanic I brought it to today is offering to silicone it
>up, but says the only real fix is to replace the oil pan (to the tune
>of $350 here in So Cal). I'm hesitant to let the mechanic touch it
>however, as I'm not convinced that it wasn't their overtorquing that
>caused this issue.
>
>My questions:
>1) Thoughts on what / who may have caused this. Is there a posibility
>that my mechanic today is telling the truth and that this was caused by
>the last mechanic (who vehemently denies using oversized plug, by the
>way).
>2) Are there issues genereally with Honda oil drain pan plugs? I found
>a website suggesting there is, but it was trying to sell a product to
>replace them. So in other words, I'm skeptical.
>3) Is there a cheaper, yet still effective long-term fix to replacing
>the oil pan?
>
>Thanks,
>Jamie
>
 >> Stay informed about: 2000 Civic Oil Drain Pan Plug Problem 

jelgie.RemoveThis@gmail.com wrote in
news:1128217252.032952.145460@o13g2000cwo.googlegroups.com:

> I took my car into a place to have the oil changed today. They said
> that the last mechanic had installed an oversized oil drain pan plug
> and that it would likely leak. Sure enough... I brought it home and it
> leaked. The mechanic I brought it to today is offering to silicone it
> up, but says the only real fix is to replace the oil pan (to the tune
> of $350 here in So Cal).


Heli-Coil will work too.


> I'm hesitant to let the mechanic touch it
> however, as I'm not convinced that it wasn't their overtorquing that
> caused this issue.



It takes some repeated overtorquing, the combined ham-fisted muscular
efforts of quite a few mechanics to perform this feat. Eventually, one of
them gets the final result, and usually doesn't want to get stuck with it.


>
> My questions:
> 1) Thoughts on what / who may have caused this. Is there a posibility
> that my mechanic today is telling the truth and that this was caused by
> the last mechanic (who vehemently denies using oversized plug, by the
> way).
> 2) Are there issues genereally with Honda oil drain pan plugs?


Oh, yes. It seems to be better now that it was ten years ago, but they're
still easy to strip than some other makes.

I think at one point Honda thickened up the metal flange that forms the
female threads in an attempt to prevent the expansion that was happening
earlier, but apparently not enough to prevent damage caused by strong-man
mechanics who just haul with all their might instead of using a torque
wrench.



> I found
> a website suggesting there is, but it was trying to sell a product to
> replace them. So in other words, I'm skeptical.
> 3) Is there a cheaper, yet still effective long-term fix to replacing
> the oil pan?


Heli-Coil. Works fine at much less cost, as the pan does not need to be
removed (don't worry about metal shards in the oil).

Here is one BIG advantage to getting the dealer to do ALL your oil changes
if you don't do them yourself: If the drain plug gets stripped, it's their
fault, and they have to replace it, as they have no one else to blame.



--
TeGGeR®

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
 >> Stay informed about: 2000 Civic Oil Drain Pan Plug Problem 

Jamie wrote:


> > My questions:
> > 1) Thoughts on what / who may have caused this.

Unless you get a confession; you can't prove the last mechanic caused the
problem. Would make for an interesting Small Claims case though...

> > 2) Are there issues genereally with Honda oil drain pan plugs?

No

> I found a website suggesting there is, but it was trying to sell a product to
>
> replace them.

Well, there you go... the information you get from the internet can be
dubious at best most of the time. Trick is separating the "wheat" from the
"chaff."

>
> > 3) Is there a cheaper, yet still effective long-term fix to replacing
> > the oil pan?
> >
> > Thanks,
> > Jamie

Looks like you're hosed because of the O/S bolt in the pan now. Check
the link below.

http://www.timesert.com/html/drainplug.html




Michael Pardee wrote:


> >
> Welcome to the club. Taking your questions out of order...
>
> Yes, there are issues with Honda drain plugs. They are intolerant of
> overtorquing, and cross-threading is bad news. Honda/Acura drain plugs
> should always be torqued with a torque wrench. Just to be clear about it, a
> new crush washer is mandatory under the plug each time, although some people
> use silicone washers.

Michael,
There are no "issues" with Honda oil pans, or drain bolts. I hardly consider
over torquing the drain bolt an "issue", Honda or otherwise.
You are correct about always using a torque wrench and new washer, in 35 years,
I've yet to strip one myself.


> In any event, don't let them try silicone glue. It will just make a crumbly
> mess of things.

This is excellent advice.

>
>
> Mike

--
Tp,

-------- __o
----- -\<. -------- __o
--- ( )/ ( ) ---- -\<.
-------------------- ( )/ ( )
-----------------------------------------

No Lawsuit Ever Fixed A Moron...
 >> Stay informed about: 2000 Civic Oil Drain Pan Plug Problem 

jelgie.TakeThisOut@gmail.com wrote:
>
> I took my car into a place to have the oil changed today. They said
> that the last mechanic had installed an oversized oil drain pan plug
> and that it would likely leak. Sure enough... I brought it home and it
> leaked. The mechanic I brought it to today is offering to silicone it
> up, but says the only real fix is to replace the oil pan (to the tune
> of $350 here in So Cal). I'm hesitant to let the mechanic touch it
> however, as I'm not convinced that it wasn't their overtorquing that
> caused this issue.
>
> My questions:
> 1) Thoughts on what / who may have caused this. Is there a posibility
> that my mechanic today is telling the truth and that this was caused by
> the last mechanic (who vehemently denies using oversized plug, by the
> way).
> 2) Are there issues genereally with Honda oil drain pan plugs? I found
> a website suggesting there is, but it was trying to sell a product to
> replace them. So in other words, I'm skeptical.
> 3) Is there a cheaper, yet still effective long-term fix to replacing
> the oil pan?
>

One of the most permanent solutions is to remove the oil pan and tig weld
on a threaded bushing after drilling out the original threads with a hole
saw. Afterwards, the oil pan is repainted and reinstalled with a new
gasket. A machine shop could probably do this for you if you don't have
access to welding equipment. Note that tig welding is best since it will
produce a strong weld which will not leak when done properly. The bushing
will supply much stronger threads for the oil drain plug than the
notoriously weak ones that Honda supplied.

Eric
 >> Stay informed about: 2000 Civic Oil Drain Pan Plug Problem